Yamaha Raptor YFM35RA страница 103 Скачать руководство пользователя | Manualshive

Страница: 103 / 142

background image

8-31

8

TIP

There are alignment marks on both drive chain
pullers and an alignment mark on each side of the
swingarm. Make sure to align the same alignment
mark on both drive chain pullers with the alignment
mark on either side of the swingarm for proper
wheel alignment.

4. Tighten the locknuts and the axle holding bolts

to the specified torques.

EBU24882

Lubricating the drive chain

The drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
and lubrication chart, otherwise it will quickly wear
out, especially when riding in dusty or wet areas.
Service the drive chain as follows.

NOTICE

ECB00561

The drive chain must be lubricated after wash-
ing the ATV or riding in the rain or wet areas.

1. Clean the drive chain with kerosene and a

small soft brush.

NOTICE:

To prevent dam-

aging the O-rings, do not clean the drive
chain with steam cleaners, high-pressure
washers or inappropriate solvents.

[ECB00571]

1. Locknut
2. Drive chain slack adjusting bolt

3. Alignment marks

Tightening torques:

Locknut:

16 Nm (1.6 m·kgf, 12 ft·lbf)

Axle holding bolt (upper):

120 Nm (12 m·kgf, 87 ft·lbf)

Axle holding bolt (lower):

73 Nm (7.3 m·kgf, 53 ft·lbf)

U1BS11E0.book Page 31 Monday, April 5, 2010 8:56 AM

«
...
101
102
103
104
105
...
»

Содержание Raptor YFM35RA















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Raptor YFM35RA

Бренд: Bad Boy Страницы: 132

Бренд: Eton America Страницы: 96

FORMULA 500 1997

Бренд: Ski-Doo Страницы: 352

GP800Y WaveRunner GP

Бренд: Yamaha Страницы: 119

FxNytro FX10M53SZ

Бренд: Yamaha Страницы: 92

FX Nytro FX10MTRY

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 146

Бренд: Yamaha Страницы: 182

Бренд: Yamaha Страницы: 140

2008 Outlander 400 EFI

Бренд: Can-Am Страницы: 599

Бренд: KAYO MOTOR Страницы: 120

FourTrax Foreman TRX520FE2 2020

Бренд: Honda Страницы: 287

Бренд: Century Страницы: 126

Бренд: Yamaha Страницы: 150

Бренд: E-TON Страницы: 225

Бренд: Evinrude Страницы: 83

Бренд: Baja motorsports Страницы: 6

Бренд: Baja motorsports Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды