Yamaha Raptor YFM35RA Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 142

Yamaha Raptor YFM35RA Скачать руководство пользователя страница 116

8-44

8

3. Insert a new bulb into the socket, push it in,

and then turn it clockwise until it stops.

4. Install the lens by installing the screws.

NOTICE:

Do not overtighten the screws,

otherwise the lens may break.

[ECB00701]

EBU25651

Removing a wheel

1. Place the ATV on a level surface.
2. Loosen the wheel nuts.

3. Elevate the ATV and place a suitable stand

under the frame.

4. Remove the nuts from the wheel.
5. Remove the wheel.

EBU25661

Installing a wheel

1. Place the ATV on a level surface.
2. Install the wheel and the nuts.
3. Lower the ATV to the ground.
4. Tighten the wheel nuts to the specified

torques.

EBU25720

Troubleshooting

Although Yamaha ATVs receive a thorough in-
spection before shipment from the factory, trouble
may occur during operation. Any problem in the fu-
el, compression, or ignition systems, for example,
can cause poor starting and loss of power.
The following troubleshooting chart represents a
quick and easy procedure for checking these vital
systems yourself. However, should your ATV re-
quire any repair, take it to a Yamaha dealer, whose
skilled technicians have the necessary tools, expe-
rience, and know-how to service the ATV properly.

1. Wheel nut

Tightening torques:

Front wheel nut:

45 Nm (4.5 m·kgf, 33 ft·lbf)

Rear wheel nut:

45 Nm (4.5 m·kgf, 33 ft·lbf)

U1BS11E0.book Page 44 Monday, April 5, 2010 8:56 AM

«
...
114
115
116
117
118
...
»

Содержание Raptor YFM35RA















































































































































Отзывы:

Нет отзывов