background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-35

6

EAU23441

Battery 

This model is equipped with a sealed-
type (MF) battery, which does not re-
quire any maintenance. There is no
need to check the electrolyte or to add
distilled water.

To charge the battery

Have a Yamaha dealer charge the bat-
tery as soon as possible if it seems to
have discharged. Keep in mind that the
battery tends to discharge more quickly
if the vehicle is equipped with optional
electrical accessories.

WARNING

EWA10760

Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-
ways shield your eyes when
working near batteries. In case
of contact, administer the fol-
lowing FIRST AID.

• EXTERNAL: Flush with plenty

of water.

• INTERNAL: Drink large quan-

tities of water or milk and im-
mediately call a physician.

• EYES: Flush with water for 15

minutes and seek prompt
medical attention.

Batteries produce explosive hy-
drogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and pro-
vide sufficient ventilation when
charging it in an enclosed
space.

KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.

To store the battery

1. If the vehicle will not be used for

more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.

2. If the battery will be stored for more

than two months, check it at least
once a month and fully charge it if
necessary.

3. Fully charge the battery before in-

stallation.

4. After installation, make sure that

the battery leads are properly con-
nected to the battery terminals.

CAUTION:

ECA10630

Always keep the battery
charged. Storing a discharged
battery can cause permanent
battery damage.

To charge a sealed-type (MF)
battery, a special (constant-volt-
age) battery charger is required.
Using a conventional battery
charger will damage the battery.
If you do not have access to a

1. Positive battery lead (red)
2. Battery

3. Negative battery lead (black)

U4P612E0.book  Page 35  Friday, May 11, 2007  3:58 PM

Содержание R6S



















































































































Отзывы: