background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-14

6

11. Add the specified amount of the

recommended engine oil, and then
install and tighten the oil filler cap.

NOTE:

Be sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.

CAUTION:

ECA11620

In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.

Make sure that no foreign mate-
rial enters the crankcase.

12. Start the engine, and then let it idle

for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.

NOTE:

After the engine is started, the engine
oil level warning light should go off if the
oil level is sufficient.

CAUTION:

ECA10400

If the oil level warning light flickers
or remains on, immediately turn the
engine off and have a Yamaha dealer
check the vehicle.

13. Turn the engine off, and then

check the oil level and correct it if
necessary.

14. Install the cowling.

EAU20070

Coolant 

The coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.

EAU38171

To check the coolant level

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion.

NOTE:

The coolant level must be checked
on a cold engine since the level
varies with engine temperature.

Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.

2. Check the coolant level in the cool-

ant reservoir.

NOTE:

The coolant should be between the
minimum and maximum level marks.

Recommended engine oil:

See page 8-1.

Oil quantity:

Without oil filter cartridge replace-
ment:

2.40 L (2.54 US qt) (2.11 Imp.qt)

With oil filter cartridge replacement:

2.60 L (2.75 US qt) (2.29 Imp.qt)

U4P612E0.book  Page 14  Friday, May 11, 2007  3:58 PM

Содержание R6S



















































































































Отзывы: