34
MU100 MIDI
1.6 Channel aftertouch
This message conveys the pressure which is applied to the keyboard
after playing a note in order to create tonal changes (for an entire MIDI
channel). The pressure can be controlled for each part. This message
will affect the currently-sounding notes.
The effect of this message will be determined by the settings of the
following parameters.
• Multi Part Parameter
1. CAT PITCH CONTROL
2. CAT FILTER CONTROL
3. CAT AMPLITUDE CONTROL
4. CAT LFO PMOD DEPTH
5. CAT LFO FMOD DEPTH
6. CAT LFO AMOD DEPTH
• Effect1 Parameter
7. CAT VARIATION CONTROL DEPTH
(Valid when the Variation Effect is assigned to a part as
Insertion)
By default, there will be no effect.
If the receive channel is a drum part, effects 5 and 6 will not apply.
If the Multi Part parameter Rcv CHANNEL AFTER TOUCH = OFF,
that part will not receive Channel Aftertouch.
1.7 Polyphonic aftertouch
This message conveys the pressure that is applied to the keyboard
after playing a note (for individual note numbers).
The pressure can be controlled independently for each note. This
message will affect currently-sounding notes.
The effect of this message is determined by the following Multi Part
parameters.
1. PAT PITCH CONTROL
2. PAT FILTER CONTROL
3. PAT AMPLITUDE CONTROL
4. PAT LFO PMOD DEPTH
5. PAT LFO FMOD DEPTH
6. PAT LFO AMOD DEPTH
By default, there will be no effect.
The effect will apply to note numbers 36...97.
In the case of either of the following Multi Part parameter settings,
that part will not receive Polyphonic Aftertouch.
Rcv CHANNEL AFTER TOUCH = OFF
PART MODE = DRUM, DRUMS1...4
2. System exclusive messages
These MIDI messages are not directly "performance data," but are
used to make settings related to the system of the MIDI device.
For example, these messages can be used to save data specific to this
device on a MIDI data filer such as the MDF3, or to exchange data
between two or more MU100 units.
By using these messages, it is possible to edit virtually all settings of
the MU100 from an external MIDI device.
However, data cannot be exchanged unless the receiving and
transmitting devices are set to the same Device Number.
2.1 Parameter changes
This devices uses the following parameter changes.
[UNIVERSAL REALTIME MESSAGE]
1)
Master Volume
[UNIVERSAL NON REALTIME MESSAGE]
1)
General MIDI System On
2)
Identity Request(INQUIRY MESSAGE)
3)
Identity Reply(INQUIRY MESSAGE)
[XG PARAMETER CHANGE]
1)
XG System on
2)
XG System parameter change
3)
Multi Effect1 parameter change
4)
Multi EQ parameter change
5)
Multi Effect2 parameter change
6)
Display parameter change
7)
Multi Part parameter change
8)
AD Part parameter change
9)
AD System parameter change
10)
Drums Setup parameter change
[MU100 NATIVE PARAMETER CHANGE 1]
1)
System parameter change
2)
Remote switch
[MU100 NATIVE PARAMETER CHANGE 2]
1)
Current Performance parameter change
[Others]
1)
Master tuning
2)
TG300 System parameter change
3)
TG300 Multi Effect parameter change
4)
TG300 Multi Part parameter change
2.1.1
Universal realtime messages
2.1.1.1
Master Volume
This system exclusive message is used to control
the volume of all channels simultaneously.
11110000
F0H
= Exclusive status
01111111
7FH
= Universal Real Time
01111111
7FH
= ID of target device
00000100
04H
= Sub-ID #1 = Device
Control Message
00000001
01H
= Sub-ID #2 = Master
Volume
*
0sssssss
SSH
= Volume LSB
0ttttttt
TTH
= Volume MSB
11110111
F7H
= End of Exclusive
or,
11110000
F0H
= Exclusive status
01111111
7FH
= Universal Real Time
0xxxnnnn
XNH
= Device Number,
xxx = don't care
00000100
04H
= Sub-ID #1 = Device
Control Message
00000001
01H
= Sub-ID #2 = Master
Volume
0sssssss
SSH
= Volume LSB
0ttttttt
TTH
= Volume MSB
11110111
F7H
= End of Exclusive
MIDI data format
