Yamaha Montage 6, Руководство по обслуживанию

Страница: 67 / 158

67
MONTAGE6/MONTAGE7
LCD display
Test items and judging conditions
22 : Internal Audio Checks whether the correct audio signals are output/receive between the SWP70 and SSP2. (There are
12 connection lines for audio output.) The full scale 441Hz sine wave is output and changed via SSP2
by each 2 channels and 4 ways of connection (8 patterns in all).
1) Press the [ENTER] button, and “ Audio 1 ON ” is shown on the LCD and a 441Hz sine wave
sound is produced. (Audio 1 test)
2) Press the [ENTER] button, and “ Audio 2 ON ” is shown on the LCD and a 441Hz sine wave
sound is produced. (Audio 2 test)
3) Press the [ENTER] button, and “ Audio 3 ON ” is shown on the LCD and a 441Hz sine wave
sound is produced. (Audio 3 test)
4) Press the [ENTER] button, and “ Audio 4 ON ” is shown on the LCD and a 441Hz sine wave
sound is produced. (Audio 4 test)
5) Press the [ENTER] button, and “ Audio 5 ON ” is shown on the LCD and a 441Hz sine wave
sound is produced. (Audio 5 test)
6) Press the [ENTER] button, and “ Audio 6 ON ” is shown on the LCD and a 441Hz sine wave
sound is produced. (Audio 6 test)
7) Press the [ENTER] button, and “ Audio 7 ON ” is shown on the LCD and a 441Hz sine wave
sound is produced. (Audio 7 test)
8) Press the [ENTER] button, and “ Audio 8 ON ” is shown on the LCD and a 441Hz sine wave
sound is produced. (Audio 8 test)
9) Press the [ENTER] button, and “ OK ” is shown on the LCD, testing is finished and the display is
changed to the test item selection screen.
23 : Touch Panel
Calibration
Checks whether the touch panel works properly or not.
1) Press the [ENTER] button. The mark “
□
” is shown at the upper left of the LCD (touch panel).
2) Touch the mark ( □ ) at the upper left.
When the touch panel is touched, the built-in buzzer sounds.
3) Then, touch the mark ( □ ) in the following order, “upper right” → “lower right” → “lower left” →
“center”, according to the display on the screen.
4) When all checks are over, “ OK ” is shown on the LCD.
Testing is finished and the display is changed to the test item selection screen.
24 : TG Interrupt
Checks that the CPU can receive the interrupt signal from the SWP70.
1) Press the [ENTER] button, and then the result is shown on the LCD.
If no problem is found:
OK
If any problem is found:
NG
2) Confirm that “OK” is shown for all items on the LCD.
3） When OK/NG of the test result is shown, testing is finished than the display is changed to the test
item selection screen.
25 : Factory Set
Sets to the factory default data. (It will take about 12 seconds.)
After writing the initial value of each parameter in the SDRAM, those data in will be written to the
eMMC (IC403).
Caution
Be careful as all the user data will be cleared. Before executing Factory Set, be sure to save important
data in the USB memory as a backup. (See page 101.)
1) Press the [ENTER] button, and then the result is shown on the LCD.
When the test result is OK, a sine wave sound is produced momentarily.
Until the result is given, “Now Executing...” is shown.
If no problem is found:
OK
If any problem is found: NG
2) Confirm that “ OK ” is shown on the LCD.
3) When OK/NG of the test result is shown, testing is finished and the display is changed to the test
item selection screen.