35
MG82CX/MG102C
2-9 Channel
equalizer
characteristics
Under 2-2 setting, check that the output level at the ST OUT L, R in each frequency when the HIGH, MID, and LOW
of EQ gain controls are moved respectively is within the range shown in Table 2-9-1 compared with the output level
when the EQ gain controls are at the center click position. If it is out of the range, change the input frequency within
the range of ±20% and check that the output level of the ST OUT L, R is within the range shown in Table 2-9-1.
* When the signal is input to CH1, CH2, CH7 L or CH9 L (MG102C), measure the output level at the ST OUT L.
* When the signal is input to CH3 L/MONO or CH5 L/MONO, measure the output level at the ST OUT L and ST OUT R.
* When the signal is input to CH8 R or CH10 R (MG102C), measure the output level at the ST OUT R.
2-10 Channel
separation
Under 2-2 setting, turn the PAN (PAN/BAL, BAL) control counterclockwise fully and check that the leakage level to
the ST OUT R is –50.0 dBu or less when the output level at the ST OUT L is set to +20.0 dBu.
* Turn the PAN (PAN/BAL, BAL) controls of all the channels counterclockwise fully.
* Set the "RETURN to ST level control" to Minimum.
* Turn the PAN (PAN/BAL, BAL) control clockwise fully and check that the leakage level to the ST OUT L is –50.0
dBu or less when the output level at the ST OUT R is set to +20.0 dBu.
* Turn the PAN (PAN/BAL, BAL) controls of all the channels clockwise fully.
* Set the "RETURN to ST level control" to Minimum.
2-11 Channel
PEAK
indicator
Under 2-2 setting, input the signal to the MIC INPUT and check that the input level at which the PEAK LED begins to
light is within the range shown in Table 2-11-1.
Check that the 0 LED lights up when the output level at the ST OUT L, R is set to +4.0 ± 2.0 dBu.
Check that the –20 LED lights up when the output level of the ST OUT L, R is set to –16.0 ±3.0 dBu.
Check that the LEDs from –20 to PEAK light up sequentially by operating the STEREO level control.
For the signal paths
q
to
!2
(excluding
q
,
r
,
y
and
u
) in Tables 2-6-1 to 2-6-6, check that the distortion is 0.1% or
less when the output level at each output except PHONES L, R is +14.0 dBu.
* Change the input signal frequency to 20 Hz, 1 kHz and 20 kHz, and measure the distortion.
* Set the CH level controls other than the measurement channel to Minimum.
* For the signal path
w
, turn the PAN control counterclockwise fully and check that the distortion is 0.1% or less
when the output level at the ST OUT L is set to +4.0 dBu.
* For the signal path
t
, turn the PAN/BAL control clockwise and counterclockwise fully and check that the distortion
is 0.1% or less when the output level at the ST OUT L, R is set to +4.0 dBu.
* For the signal path
i
, check all the outputs when the signal is input to CH7 L, and check only the ST OUT L when
the signal is input to CH9 L (MG102C).
Table 2-9-1
INPUT
EQ gain control
Input
frequency
Variation
Width
ST OUT (L, R)
PHONE
(LINE)
1, 2
3 L/MONO
5 L/MONO
7 L, 8 R
9 L (MG102C),
10 R (MG102C)
HIGH
Maximum
10 kHz
+12.0 dB ± 2.0 dB
Minimum
–12.0 dB ± 2.0 dB
MID
Maximum
2.5 kHz
+15.0 dB ± 2.0 dB
Minimum
–15.0 dB ± 2.0 dB
LOW
Maximum
100 Hz
+12.0 dB ± 2.0 dB
Minimum
–12.0 dB ± 2.0 dB
* CH7/CH8 and CH9/CH10 (MG102C) have only HIGH and LOW controls.
Table 2-11-1
PEAK LED
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299