Yamaha Majesty YP400V Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 102

Yamaha Majesty YP400V Скачать руководство пользователя страница 71

PERIODIC MAINTENANCE AND MINOR REPAIR

6-30

2

3

4

5

6

7

8

9

EAU23090

Checking and lubricating the
cables

The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.

WARNING

EWA10710

Damage to the outer housing of ca-
bles may result in internal rusting
and cause interference with cable
movement. Replace damaged ca-
bles as soon as possible to prevent

unsafe conditions.

EAU23111

Checking and lubricating the
throttle grip and cable

The operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated at
the intervals specified in the periodic
maintenance chart.

EAU23170

Lubricating the front and rear
brake levers

The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic main-
tenance and lubrication chart.

Recommended lubricant:

Yamaha Chain and Cable Lube or
engine oil SAE 10W-30 (API SE)

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

«
...
69
70
71
72
73
...
»

Содержание Majesty YP400V







































































































Отзывы:

Нет отзывов