Yamaha LZ200 Скачать руководство пользователя

Страница: 56 / 106

Operation

EMU36490

Flushing device

Check that flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

flushing device is not properly connect-
ed, cooling water can leak out and the en-
gine can overheat during operation.

[ECM01800]

EMU36940

Install cowling

Be sure that all cowling lock levers are
released.

Be sure that the rubber seal is seated all
the way around the engine.

Place the cowling on top of the seal.

Check to be sure it fits properly in the
rubber seal.

Move the levers to lock the cowling as
shown.

NOTICE:

If the cowling is not

installed correctly, water spray under
the cowling can damage the engine,
or the cowling can blow off at high
speeds.

[ECM01990]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

1. Fitting
2. Flushing device

ZMU03989

ZMU06050

ZMU06131

ZMU06127

✩✫✳✬✤✲ ✣

2019 Yamaha Motor Corporation, U.S.A.

Содержание LZ200











































































































Результаты поиска

Содержание LZ200

Отзывы:

Похожие инструкции для LZ200

Бренды по названию

Популярные бренды

Yamaha LZ200, Руководство оператора

Результаты поиска

Содержание LZ200

Отзывы:

Похожие инструкции для LZ200

Бренды по названию

Популярные бренды