manualshive.com logo in svg

Yamaha LZ200, Руководство оператора

Поделиться
Скачать
Yamaha LZ200 Скачать руководство пользователя страница 63

 

Operation

 

57

 

5.

Immediately after the engine starts, re-
lease the main switch to return it to “

”

(on). 

 

NOTICE:

 

 Never turn the main

switch to “

” (start) while the en-

gine is running. Do not keep the start-
er motor turning for more than 5
seconds. If the starter motor is turned
continuously for more than 5 sec-
onds, the battery will be quickly dis-
charged, thus making it impossible to
start the engine. The starter can also
be damaged. If the engine will not
start after 5 seconds of cranking, re-
turn the main switch to “

” (on), wait

10 seconds, then crank the engine
again.

 

 [ECM00192]

 

 

 

EMU36510

 

Checks after starting engine

 

EMU36522

 

Cooling water

 

Check for a steady flow of water from the

cooling water pilot hole. A continuous flow of
water from the pilot hole indicates that the
water pump is pumping water through the
cooling water passages. If the cooling water
passages are frozen, it may take a while for
water to start flowing out of the pilot hole.

NOTICE

 

ECM01810 

 

If water is not flowing out of the pilot hole
at all times while the engine is running,
overheating and serious damage could
occur. Stop the engine and check wheth-
er the cooling water inlet on the lower
case or the cooling water pilot hole is
blocked. Consult your Yamaha dealer if
the problem cannot be located and cor-

 

rected.

 

EMU27670

 

Warming up engine

 

EMU27704

 

Electric start and prime start models

 

After starting the engine, allow it to idle for 3
minutes to warm up. Failure to do so will
shorten engine life.

 

EMU36531

 

Checks after engine warm up

 

EMU36540

 

Shifting

 

While tightly moored, and without applying
throttle, confirm that the engine shifts
smoothly into forward and reverse, and back

ON

START

OFF

ZMU01881

START

ON

ZMU04590

ZMU01882

✩✫✳✬✤✲ ✪  

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание LZ200











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды