Yamaha LZ200 Скачать руководство пользователя

Страница: 64 / 106

Operation

to neutral.

EMU31721

Stop switches

●

Confirm that turning the main switch to the
“

” (off) position stops the engine.

●

Confirm that removing the clip from the en-
gine shut-off switch stops the engine.

●

Confirm that the engine cannot be started
with the clip removed from the engine
shut-off switch.

EMU31732

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near

you.

NOTICE

ECM01610

Warm up the engine before shifting into
gear. Until the engine is warm, the idle
speed may be higher than normal. High
idle speed can prevent you from shifting
back to neutral. If this occurs, stop the
engine, shift to neutral, then restart the

engine and allow it to warm up.

To shift out of neutral
1.

Pull the neutral interlock trigger up (if
equipped).

Move the remote control lever firmly for-
ward (for forward gear) or rearward (for
reverse gear) about 35° (a detent can be
felt).

To shift from in gear (forward/reverse) to
neutral
1.

Close the throttle so that the engine
slows to idle speed.

1. Neutral interlock trigger

✩✫✳✬✤✲ ✫

2019 Yamaha Motor Corporation, U.S.A.

Содержание LZ200











































































































Результаты поиска

Содержание LZ200

Отзывы:

Похожие инструкции для LZ200

Бренды по названию

Популярные бренды

Yamaha LZ200, Руководство оператора

Результаты поиска

Содержание LZ200

Отзывы:

Похожие инструкции для LZ200

Бренды по названию

Популярные бренды