Yamaha LZ150A Скачать руководство пользователя

Страница: 65 / 120

3-22

EMU00316

CRUISING IN OTHER

CONDITIONS

CRUISING IN SALT WATER

After operating in salt water, wash out the
cooling-water passages with fresh water
to prevent them from becoming clogged-
up with salt deposits.

NOTE:

Refer to cooling system flushing instruc-
tions in “TRANSPORTING AND STORING
OUTBOARD MOTOR”.

CRUISING IN TURBID WATER

It is strongly recommended that the
optional chromium-plated water-pump kit
be installed if the outboard is to be used
in turbid (muddy) water conditions.

EMU00303

PROCEDURE FOR TILTING DOWN

Power trim/tilt model

Push the power trim/tilt switch “UP”
until the engine is supported by the
tilt rod.

Release the tilt-support lever.

Push the power trim/tilt switch “DN”
(Down) to lower the engine to the
desired position.

411045

68F-9-13-3 <2nd> 4/23/01 11:59 AM Page 23

Содержание LZ150A

























































































































Результаты поиска

Содержание LZ150A

Отзывы:

Похожие инструкции для LZ150A

Бренды по названию

Популярные бренды

Yamaha LZ150A, Руководство пользователя

Результаты поиска

Содержание LZ150A

Отзывы:

Похожие инструкции для LZ150A

Бренды по названию

Популярные бренды