Yamaha LZ150A Скачать руководство пользователя

Страница: 42 / 120

2-21

001094

703026

OFF

START OFF

START

213032

905012

EMU00172

OIL LEVEL WARNING / OIL FILTER
CLOGGING WARNING

This engine has an oil level warning sys-
tem. If oil level falls below lower limit, the
warning device will activate.

(

); Included (—); N/A

If the warning system has been activated,
stop the engine and check for the cause.

NOTE:

The warning for oil filter clogging is simi-
lar to the warnings for low oil level and
overheating. For easy troubleshooting, it
is advisable to check for engine overheat-
ing first, then oil level and finally oil filter
clogging.

Oil filter

Warning device

Tiller

Remote

activation

control

model

The engine speed
will automatically

decrease to about
2,000 r/min.

The oil level warning

indicator will come on.

The buzzer will sound.

68F-9-13-2 <2nd> 4/23/01 11:53 AM Page 22

Содержание LZ150A

























































































































Результаты поиска

Содержание LZ150A

Отзывы:

Похожие инструкции для LZ150A

Бренды по названию

Популярные бренды

Yamaha LZ150A, Руководство пользователя

Результаты поиска

Содержание LZ150A

Отзывы:

Похожие инструкции для LZ150A

Бренды по названию

Популярные бренды