Yamaha LZ150A Скачать руководство пользователя страница 58

Страница: 58 / 120

3-15

701043

701044

EMU00261

SHIFTING

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

To change the shifting position from for-
ward to reverse or vice-versa, close the
throttle first so that the engine idles (or
runs at low speeds).

EMU00264

FORWARD

Pull up the neutral interlock trigger (If
equipped) and move the remote control
lever quickly and firmly from Neutral to
Forward.

EMU00269

REVERSE

When operating in Reverse, go slowly. Do
not open the throttle more than half.
Otherwise, the boat may become unsta-
ble, which could result in loss of control
and an accident.

Pull up the neutral interlock trigger (If
equipped) and move the remote control
lever quickly and firmly from Neutral to
Reverse.

702015

702016

68F-9-13-3 <2nd> 4/23/01 11:59 AM Page 16

Содержание LZ150A

























































































































Результаты поиска

Содержание LZ150A

Отзывы:

Бренды по названию

Популярные бренды

Yamaha LZ150A, Руководство пользователя

Результаты поиска

Содержание LZ150A

Отзывы:

Бренды по названию

Популярные бренды