Yamaha LZ150A Скачать руководство пользователя

Страница: 59 / 120

3-16

OFF

703046

START

OFF

701023

EMU00273

STOPPING ENGINE

Let it cool off for a few minutes at idle or
low speed first. Stopping the engine
immediately after operating at high speed
is not recommended.

EMU00276*

Turn the main switch to “OFF”.

If there is a fuel joint or a fuel cock on
the boat, disconnect the fuel line or
close the fuel cock after stopping the
engine.

Tighten the air vent screw on the fuel
tank cap after stopping the engine, if
it is equipped.

Remove the key if the boat will be left
unattended.

NOTE:

The engine can also be stopped by
pulling the lanyard and removing the lock
plate from the engine stop lanyard switch
(then turning the main switch to “OFF”).

68F-9-13-3 <2nd> 4/23/01 11:59 AM Page 17

Содержание LZ150A

























































































































Результаты поиска

Содержание LZ150A

Отзывы:

Похожие инструкции для LZ150A

Бренды по названию

Популярные бренды

Yamaha LZ150A, Руководство пользователя

Результаты поиска

Содержание LZ150A

Отзывы:

Похожие инструкции для LZ150A

Бренды по названию

Популярные бренды