Yamaha LX150A Скачать руководство пользователя | Manualshive

Страница: 67 / 125

background image

E

3-22

UP

DOWN

UP

DN

702014

403035*

DOWN

UP

702042

EMU01201

PROCEDURE FOR TILTING UP

Power trim/tilt model

1)

If there is a fuel joint or a fuel cock on
the boat, disconnect the fuel line or
close the fuel cock.

2)

Push the power trim/tilt switch “UP”
until the outboard has tilted up com-
pletely.

3)

Turn the tilt-support lever toward you
and support the engine.

w

After tilting the engine, be sure to sup-
port it with the tilt-support lever.
Otherwise, the engine could fall back
down suddenly if oil in the power
trim/tilt unit should lose pressure.

4)

Once the engine is supported with the
tilt-support lever, push the power
trim/tilt switch DOWN to retract the
trim rods.

c

C

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growths and corrosion
which could damage the power trim/tilt
mechanism.

67K-9-13-3 4/19/01 10:43 AM Page 23

«
...
65
66
67
68
69
...
»

Содержание LX150A






























































































































Отзывы:

Нет отзывов

Похожие инструкции для LX150A

Бренд: Microchip Technology Страницы: 17

Бренд: IBASE Technology Страницы: 84

microComponents mp6-XEVA

Бренд: Bartels Mikrotechnik Страницы: 9

Бренд: Atmel Страницы: 30

Бренд: Advantech Страницы: 104

Бренд: JETWAY Страницы: 57

Бренд: AZZA Страницы: 61

Бренд: ASROCK Страницы: 160

Бренд: DFI Страницы: 71

EVAL-AD7175-8SDZ

Бренд: Analog Devices Страницы: 11

Бренд: Analog Devices Страницы: 32

Бренд: WinSystems Страницы: 85

Бренд: PCchips Страницы: 44

Бренд: Abit Страницы: 24

Бренд: Siemens Nixdorf Страницы: 20

Бренд: IBT Technologies Страницы: 56

Бренд: Foxconn Страницы: 87

Бренд: Foxconn Страницы: 117

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды