manualshive.com logo in svg

Yamaha LX150A, Руководство пользователя

Поделиться
Скачать
Yamaha LX150A Скачать руководство пользователя страница 68

EMU00316

CRUISING IN OTHER

CONDITIONS

CRUISING IN SALT WATER

After operating in salt water, wash out the
cooling-water passages with fresh water
to prevent them from becoming clogged-
up with salt deposits.

NOTE:

Refer to cooling system flushing instruc-
tions in “TRANSPORTING AND STORING
OUTBOARD MOTOR”.

CRUISING IN TURBID WATER

It is strongly recommended that the
optional chromium-plated water-pump kit
be installed if the outboard is to be used
in turbid (muddy) water conditions.

E

3-23

EMU00303

PROCEDURE FOR TILTING DOWN

Power trim/tilt model

1)

Push the power trim/tilt switch “UP”
until the engine is supported by the
tilt rod.

2)

Release the tilt-support lever.

3)

Push the power trim/tilt switch “DN”
(Down) to lower the engine to the
desired position.

 67K-9-13-3  4/19/01 10:43 AM  Page 24

Содержание LX150A






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды