Yamaha LX150A страница 44 Скачать руководство пользователя

Страница: 44 / 125

2-21

001094

703026

OFF

START OFF

START

213022

905012

EMU00172

OIL LEVEL WARNING / OIL FILTER
CLOGGING WARNING

This engine has an oil level warning sys-
tem. If oil level falls below lower limit, the
warning device will activate.

(

); Included (—); N/A

If the warning system has been activated,
stop the engine and check for the cause.

NOTE:

The warning for oil filter clogging is simi-
lar to the warnings for low oil level and
overheating. For easy troubleshooting, it
is advisable to check for engine overheat-
ing first, then oil level and finally oil filter
clogging.

Oil filter

Warning device

Tiller

Remote

activation

control

model

The engine speed
will automatically

decrease to about
2,000 r/min.

The oil level warning

indicator will come on.

The buzzer will sound.

67K-9-13-2 4/19/01 10:44 AM Page 22

Содержание LX150A






























































































































Результаты поиска

Содержание LX150A

Отзывы:

Похожие инструкции для LX150A

Бренды по названию

Популярные бренды

Yamaha LX150A, Руководство пользователя

Результаты поиска

Содержание LX150A

Отзывы:

Похожие инструкции для LX150A

Бренды по названию

Популярные бренды