Yamaha LS9-16 Скачать руководство пользователя страница 30

Страница: 30 / 80

LS9 Editor Owner’s Manual

❏

EQUALIZER

LIBRARY

Accesses the INPUT EQ page of the LIBRARY window.

Switches the EQ on/off.

EQ graph

Indicates the response for the EQ of the currently selected channel. To reset the EQ to flat response, hold down
the <Ctrl>(<

>) key of your computer keyboard and click the graph (The HPF setting will remain).

FREQUENCY

GAIN

These knobs adjust the Q, center frequency, and boost/cut amount for the four bands LOW, LO-MID, HI-MID,
and HIGH.

HIGH shelving

If this button is on, the HIGH EQ will be switched to a shelving type (the Q knob of the HIGH EQ will disap-
pear).

LPF (Low Pass Filter)

If this button is on, the HIGH EQ will function as a low pass filter. The Q knob of the HIGH EQ will disappear,
and the GAIN knob will act as the low pass filter on/off switch.

LOW shelving

If this button is on, the LOW EQ will be switched to a shelving type (the Q knob of the LOW EQ will disappear).

TYPE I/TYPE II (EQ type)

Selects either TYPE I (the same algorithm as on previous Yamaha digital mixers) or TYPE II (a newly developed
algorithm) as the EQ type.

ATT (Attenuation)

Adjusts the amount of attenuation/gain.

Содержание LS9-16

















































































Результаты поиска

Содержание LS9-16

Отзывы:

Похожие инструкции для LS9-16

Бренды по названию

Популярные бренды

Yamaha LS9-16, Руководство пользователя

Результаты поиска

Содержание LS9-16

Отзывы:

Похожие инструкции для LS9-16

Бренды по названию

Популярные бренды