Yamaha GP1300R WaveRunner 2008 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 98

background image

Trouble recovery

84

CAUTION:

ECJ00660

●

Place a suitable clean cloth or carpeting
underneath the watercraft to protect it
from abrasions and scratches.

●

Always turn the watercraft over onto its
port (left) side.

●

When turning the watercraft on its side,
support the bow so that the handlebars
are not bent or damaged.

(2) Remove any weeds or debris from

around the drive shaft, impeller, jet pump
housing, and jet thrust nozzle.
If debris is difficult to remove, consult a
Yamaha dealer.

CAUTION:

ECJ00670

Always avoid operating your watercraft in
areas where weed growth is thick. If travel-
ing in weeded areas is unavoidable, oper-
ate the engine alternately at partial throttle
and full throttle. Weeds tend to accumu-
late more at a steady speed and at trolling
speed. If weeds clog the jet intake or im-
peller area and cause cavitation, follow the
cleaning procedure above.

EJU34640

Jumping the battery

If the watercraft battery has run down, the en-
gine can be started using a 12-volt booster
battery and jumper cables.

WARNING

EWJ00790

Battery electrolyte is poisonous and dan-
gerous, causing severe burns, etc. Elec-
trolyte contains sulfuric acid. Avoid
contact with skin, eyes, or clothing.
Antidotes
External: Flush with water.
Internal: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten

egg, or vegetable oil. Call a physician im-
mediately.
Eyes: Flush with water for 15 minutes and
get prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flames, cigarettes, etc., well away.
If using or charging the battery in an en-
closed space, make sure that it is well ven-
tilated. Always shield your eyes when
working near batteries.
KEEP OUT OF THE REACH OF CHILDREN.

EJU34651

Connecting the jumper cables

(1) Connect the positive (+) jumper cable to

the positive (+) battery terminals of both
batteries.

(2) Connect one end of the negative (–)

jumper cable to the negative (–) battery
terminal of the booster battery.

(3) Connect the other end of the negative (–)

jumper cable to an unpainted bolt on the
cylinder head.

CAUTION:

ECJ00680

Do not connect the end of the negative (–)
jumper cable to the negative (–) battery
terminal of the watercraft battery! Make
sure that all connections are secure and
correct before attempting to start the en-

1

Positive (+) jumper cable

2

Negative (–) jumper cable

3

Booster battery

UF1G15E0.book Page 84 Thursday, May 31, 2007 9:09 AM

«
...
87
88
89
90
91
...
»

Содержание GP1300R WaveRunner 2008



































































































Отзывы:

Нет отзывов

Похожие инструкции для GP1300R WaveRunner 2008

Бренд: Jeanneau Страницы: 80

Бренд: Falcon Страницы: 41

Genesis Console 310

Бренд: Walker Bay Страницы: 12

TomCat 255 Pilothouse

Бренд: C-Dory Marine Страницы: 20

Бренд: grabner Страницы: 4

Бренд: Solo Skif Страницы: 9

Samba Jeanneau Sun Odyssey 45 2007

Бренд: Hermes Yachting Страницы: 26

Бренд: Sea-doo Страницы: 14

Бренд: Sea-doo Страницы: 88

Бренд: Kingfisher Страницы: 35

Бренд: Polaris Страницы: 331

Бренд: BENETEAU Страницы: 28

SUN ODYSSEY 49 DS

Бренд: Jeanneau Страницы: 126

WaveRunner GP800R 2001

Бренд: Yamaha Страницы: 123

Бренд: 3d Страницы: 17

Бренд: Hobie Страницы: 16

600 DAY CRUISER 15

Бренд: Coaster Страницы: 39

Бренд: Seamax Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды