Yamaha GP1300R WaveRunner 2008 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 98

background image

Maintenance and care

74

Remove and inspect the spark plugs periodi-
cally; heat and deposits will cause the spark
plugs to slowly break down and erode. If elec-
trode erosion becomes excessive, or if carbon
and other deposits are excessive, replace the
spark plug with the specified plug.

Measure the spark plug gap with a wire thick-
ness gauge. Replace the spark plugs or ad-
just the gap to specification if necessary.

To install a spark plug:
(1) Clean the gasket surface.
(2) Wipe any dirt from the threads of the

spark plug.

(3) Install the spark plug, and then tighten it

to the specified torque.

(4) Install the spark plug cap.

NOTE:

●

Wipe off any water on the spark plug or in-
side the spark plug cap before installing the

cap. Push the spark plug cap down until it is
securely installed.

●

If a torque wrench is not available when you
are installing a spark plug, a good estimate
of the correct torque is 1/4 turn to 1/2 turn
past finger tight using the spark plug
wrench included in the tool kit. Have the
spark plug adjusted to the correct torque
with a torque wrench as soon as possible.

EJU34411

Lubrication points

To keep moving parts sliding or rotating
smoothly, coat them with water-resistant
grease.

●

Throttle cable (handlebar end)
Squeeze the throttle lever and remove the
seal. Spray a rust inhibitor into the outer ca-
ble. Refit the seal securely.

Specified spark plug:

BR8ES-11

1

Spark plug gap

Spark plug gap:

1.0–1.1 mm (0.039–0.043 in)

Spark plug tightening torque:

25.0 Nm (18.4 ft-lb) (2.55 kgf-m)

Recommended water-resistant grease:

Yamaha Marine Grease/Yamaha
Grease A

1

Seal

UF1G15E0.book Page 74 Thursday, May 31, 2007 9:09 AM

«
...
77
78
79
80
81
...
»

Содержание GP1300R WaveRunner 2008



































































































Отзывы:

Нет отзывов

Похожие инструкции для GP1300R WaveRunner 2008

Бренд: Walker Bay Страницы: 8

Mackinaw 156 Canoe

Бренд: KL Industries Страницы: 5

32 Express 2010

Бренд: Pro-Line Boats Страницы: 72

Invitation Triss Racer

Бренд: BOMBARDIER Страницы: 23

Бренд: Banzai Страницы: 10

1998 GSX Limited 5625

Бренд: Sea-doo Страницы: 11

Бренд: Sea-doo Страницы: 15

Бренд: Sea-doo Страницы: 372

Бренд: Bush Страницы: 15

Бренд: Hunter Страницы: 161

Бренд: Mercury Страницы: 522

Бренд: BENETEAU Страницы: 138

Бренд: Sailfish Страницы: 24

Бренд: Sailfish Страницы: 43

Бренд: Feathercraft Страницы: 23

Бренд: Raymarine Страницы: 31

WaveRunner FX SVHO 2017

Бренд: Yamaha Страницы: 118

Бренд: Ocean Kayak Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды