Yamaha GP1300R WaveRunner 2008 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 98

background image

Maintenance and care

72

EJU34210

Checking the fuel system

WARNING

EWJ00380

Gasoline is highly flammable and explo-
sive. Failure to check for and repair any
fuel leakage could result in a fire or explo-
sion. A fire or explosion can cause severe
injury or death. Shut the engine off. Do not
smoke. Avoid spilling gasoline.
Fuel in the fuel lines is pressurized.
Fuel can spray out and cause injury or a
fire hazard if a fuel line is disconnected.
Do not run the engine with a fuel line dis-
connected.

Check the fuel system for leaks, cracks, and
malfunctions. If any problem is found, consult
a Yamaha dealer.

Check:

●

Fuel tank filler cap and seal for damage.

●

Fuel in fuel tank for water and dirt.

●

Fuel tank for damage, cracks, and leakage.

●

Fuel hoses and joints for damage, cracks,
and leakage.

●

Air bleeding passages for leakage.

EJU34230

Fuel tank

Check the fuel tank for leakage and for water
in the tank. If water is found in the fuel system,
or if the fuel tank needs to be cleaned, have a
Yamaha dealer service the watercraft.

EJU34240

Checking the oil injection system

Check the oil injection system for leakage,
cracks, and malfunctions. Have a Yamaha
dealer repair the oil injection system if neces-
sary.

Check:

●

Oil tank for damage, cracks, and leakage.

●

Oil in the oil tank for water and dirt.

●

Oil hoses and joints for damage, cracks,
and leakage.

●

Oil filter for dirt.

●

Oil pump for leakage.

EJU34250

Oil tank

Check the oil tank for leakage and for water in
the tank. If water is found in the oil injection
system, or if the oil tank needs to be cleaned,
have a Yamaha dealer service the watercraft.

EJU34260

Oil filter

Have a Yamaha dealer check the oil filter for
dirt and clogs.

EJU34321

Checking the jet thrust nozzle angle

Check the handlebars and jet thrust nozzle for
smooth operation.
Turn the handlebars as far as possible to the
right and left and check that the difference of
distances A and B between the jet thrust noz-
zle and the nozzle is within specification.

1

Fuel tank

UF1G15E0.book Page 72 Thursday, May 31, 2007 9:09 AM

«
...
75
76
77
78
79
...
»

Содержание GP1300R WaveRunner 2008



































































































Отзывы:

Нет отзывов

Похожие инструкции для GP1300R WaveRunner 2008

Бренд: TAKACAT Страницы: 12

Бренд: C&L Marine Страницы: 14

Бренд: Hobie Страницы: 33

Бренд: Hobie Страницы: 24

Бренд: Hobie Страницы: 2

Mirage Tandem Island

Бренд: Hobie Страницы: 52

Бренд: komodo Страницы: 12

Бренд: Grand Banks Страницы: 51

Бренд: AFRI-CAT Страницы: 24

Бренд: Grady-White Boats Страницы: 90

Бренд: Kingfisher Страницы: 35

Бренд: Bavaria Страницы: 90

Ocean Runner 290

Бренд: Mercury Страницы: 46

Nautilus 11 DLX

Бренд: AB Inflatables Страницы: 52

Бренд: Jeanneau Страницы: 114

Бренд: Old Town Canoe Co. Страницы: 14

Бренд: Latitude 46 Страницы: 58

Бренд: Yamaha Страницы: 277

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды