Yamaha GP1300R WaveRunner 2008 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 98

background image

Operation

45

EJU32280

Pre-operation check points

EJU32300

Engine compartment

Ventilate the engine compartment before
each use.
To ventilate the engine compartment, remove
the seat and front storage compartment. (See
“Seat” on page 27 and “Front storage com-
partment” on page 38 for more information.)
Leave the engine compartment open for a few
minutes to allow any fuel vapors to escape.
While the engine compartment is open, check
for loose electrical connections.

WARNING

EWJ00460

Failure to ventilate the engine compart-
ment could result in a fire or explosion. Do
not start the engine if there is a fuel leak or
a loose electrical connection.

EJU32350

Hull and deck

Check the hull and deck for cracks and other
damage. If any damage is found, have a
Yamaha dealer repair the watercraft.

EJU32371

Fuel and oil systems

Check the fuel system for leakage, cracks,
and malfunctions before each use. (See page
72 for check points and correct procedures.)
(1) Remove the fuel tank filler cap to release

any pressure that might have built up in
the fuel tank.

(2) Remove the seat and front storage com-

partment. (See “Seat” on page 27 and
“Front storage compartment” on page 38
for more information.)

(3) Check the fuel and oil levels in the tanks

and replenish if necessary. (See page 42
for refueling procedures and page 42 for
oil tank filling procedures.)

(4) Install the fuel tank filler cap, seat, and

front storage compartment.

EJU32420

Water separator

Check the water separator for water. The wa-
ter separator retains any water that may have
entered through the fuel tank breather hose if
the watercraft was capsized. Normally, the
water separator is empty.

If water remains in the water separator, drain
it by removing the drain screw. Place a drain
pan under the water separator to catch the
draining water or use a dry cloth to soak up
any water that could spill into the watercraft. If
any water spills into the watercraft, be sure to
wipe it up with a dry cloth. Also, be sure to in-
stall the drain screw after draining the water
separator.

EJU32440

Bilge

Check the bilge for moisture and fuel residue.
This watercraft is equipped with a convention-
al jet vacuum bilge draining system and an

1

Water separator

2

Drain screw

UF1G15E0.book Page 45 Thursday, May 31, 2007 9:09 AM

«
...
48
49
50
51
52
...
»

Содержание GP1300R WaveRunner 2008



































































































Отзывы:

Нет отзывов

Похожие инструкции для GP1300R WaveRunner 2008

Бренд: Anacortes Yacht Charters Страницы: 22

Бренд: Sea Eagle Страницы: 8

Бренд: RS SAILING Страницы: 70

Бренд: Edgewater Networks Страницы: 49

60 Day Cruiser 2020

Бренд: YAMARIN Страницы: 100

Бренд: Incept Страницы: 4

Бренд: Four winns Страницы: 139

SHIRE 14 130 WB

Бренд: Barrus Страницы: 50

Бренд: Polaris Страницы: 90

Бренд: DE WIT WORKBOATS Страницы: 42

Бренд: Ocean Kayak Страницы: 4

Бренд: TALAMEX Страницы: 17

Бренд: Lowell Страницы: 2

Бренд: Grady-White Boats Страницы: 78

Бренд: Point 65 Страницы: 5

Бренд: Monterey Страницы: 69

268 SC Sport Cruiser

Бренд: Monterey Boats Страницы: 135

278 SC Sport Cruiser

Бренд: Monterey Boats Страницы: 165

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды