Yamaha FZ-6 FZS6C Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 108

background image

OPERATION AND IMPORTANT RIDING POINTS

5-3

5

CAUTION:

ECA10260

●

Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.

●

Always use the clutch while
changing gears to avoid damag-
ing the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.

EAU16680

To start out and accelerate

1. Pull the clutch lever to disengage

the clutch.

2. Shift the transmission into first

gear. The neutral indicator light
should go out.

3. Open the throttle gradually, and at

the same time, release the clutch
lever slowly.

4. At the recommended shift points

shown in the following table, close
the throttle, and at the same time,
quickly pull the clutch lever in.

5. Shift the transmission into second

gear. (Make sure not to shift the
transmission into the neutral posi-
tion.)

6. Open the throttle part way and

gradually release the clutch lever.

7. Follow the same procedure when

shifting to the next higher gear.

NOTE:

Always shift gears at the recommended
shift points.

EAU16700

To decelerate

1. Apply both the front and the rear

brakes to slow the motorcycle.

2. Shift the transmission into first

gear when the motorcycle reaches
25 km/h (15.5 mi/h). If the engine is
about to stall or runs very roughly,
pull the clutch lever in and use the
brakes to stop the motorcycle.

3. Shift the transmission into the neu-

tral position when the motorcycle
is almost completely stopped. The
neutral indicator light should come
on.

EAU16740

Recommended shift points

The recommended shift points during
acceleration and deceleration are
shown in the table below.

Shift up points:

1st

→

2nd: 30 km/h (19 mi/h)

2nd

→

3rd: 45 km/h (28 mi/h)

3rd

→

4th: 60 km/h (37 mi/h)

4th

→

5th: 75 km/h (47 mi/h)

5th

→

6th: 90 km/h (56 mi/h)

Shift down points:

6th

→

5th: 25 km/h (15.5 mi/h)

5th

→

4th: 25 km/h (15.5 mi/h)

4th

→

3rd: 25 km/h (15.5 mi/h)

3rd

→

2nd: 25 km/h (15.5 mi/h)

2nd

→

1st: —

U4S811E0.book Page 3 Wednesday, August 8, 2007 1:14 PM

«
...
39
40
41
42
43
...
»

Содержание FZ-6 FZS6C













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ-6 FZS6C

Бренд: DAELIM Страницы: 20

Бренд: Honda Страницы: 201

Бренд: Baja motorsports Страницы: 20

Бренд: Suzuki Страницы: 447

PowerCom INNOVA Plus Business

Бренд: AKE Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 34

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 92

WARRIOR XV17PCT

Бренд: Yamaha Страницы: 97

WARRIOR XV17PCC

Бренд: Yamaha Страницы: 97

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 95

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 98

Wild Star XV1600A

Бренд: Yamaha Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды