Yamaha FZ-6 FZS6C Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 108

background image

OPERATION AND IMPORTANT RIDING POINTS

5-1

5

EAU15950

WARNING

EWA10270

●

Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly un-
derstand.

●

Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.

●

Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.

EAU40192

Starting the engine

In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met.

●

The transmission is in the neutral
position.

●

The transmission is in gear with
the clutch lever pulled and the sid-
estand up.

WARNING

EWA10290

●

Before starting the engine,
check the function of the igni-
tion circuit cut-off system ac-
cording to the procedure
described on page 3-16.

●

Never ride with the sidestand
down.

1. Turn the key to “ON” and make

sure that the engine stop switch is
set to “

”.

CAUTION:

ECA15481

The following warning lights should
come on for a few seconds, then go
off.

●

Oil level warning light

●

Coolant temperature warning
light

●

Engine trouble warning light

If a warning light does not go off, see
page 3-2 for the corresponding
warning light circuit check.

2. Shift the transmission into the neu-

tral position.

NOTE:

When the transmission is in the neutral
position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical cir-
cuit.

3. Start the engine by pushing the

start switch.

NOTE:

If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the en-
gine more than 10 seconds on any one
attempt.

U4S811E0.book Page 1 Wednesday, August 8, 2007 1:14 PM

«
...
37
38
39
40
41
...
»

Содержание FZ-6 FZS6C













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ-6 FZS6C

Бренд: Cannondale Страницы: 61

Бренд: DAELIM Страницы: 20

Бренд: Yamaha Страницы: 650

Freeride E-XC 2019

Бренд: KTM Страницы: 44

Бренд: Dakota Digital Страницы: 2

Бренд: Evotech Страницы: 84

Бренд: IRC Страницы: 2

Бренд: Caberg Страницы: 16

Бренд: hepco & becker Страницы: 4

Бренд: DYNATEK Страницы: 7

Бренд: VESPA Страницы: 317

Бренд: MZ Страницы: 204

Бренд: Benelli Страницы: 243

Бренд: Atra Страницы: 3

TOURATECH 22112929044

Бренд: KTM Страницы: 97

Бренд: Honda Страницы: 66

Бренд: Honda Страницы: 78

Бренд: Honda Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды