Yamaha FZ-6 FZS6C Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 108

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-25

6

EAU36501

Rear brake light switch

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, have a Yamaha dealer ad-
just the brake light switch.

EAU22390

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU36890

Front brake pads

Each front brake pad is provided with
wear indicators, which allows you to
check the brake pad wear without hav-
ing to disassemble the brake. To check
the brake pad wear, check the position
of the wear indicators while applying
the brake. If a brake pad has worn to

the point that a wear indicator almost
touches the brake disc, have a Yamaha
dealer replace the brake pads as a set.

EAU22500

Rear brake pads

Check each rear brake pad for damage
and measure the lining thickness. If a
brake pad is damaged or if the lining
thickness is less than 1.0 mm (0.04 in),
have a Yamaha dealer replace the
brake pads as a set.

1. Rear brake light switch

2. Rear brake light switch adjusting nut

1. Brake pad wear indicator

1. Lining thickness

U4S811E0.book Page 25 Wednesday, August 8, 2007 1:14 PM

«
...
65
66
67
68
69
...
»

Содержание FZ-6 FZS6C













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ-6 FZS6C

Бренд: Kappa Страницы: 4

Бренд: Yamaha Страницы: 92

TRIUMPH Bonneville T 120

Бренд: hepco & becker Страницы: 4

Бренд: CRATONI Страницы: 61

TorqDrive Clutch Pack

Бренд: Rekluse Страницы: 18

TXT PRO - PART LIST 2005

Бренд: GAS GAS Страницы: 38

Бренд: GAS GAS Страницы: 144

Бренд: DYNATEK Страницы: 12

Бренд: IBEX Страницы: 3

YZF-R1P 2001-2003

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 36

Бренд: Yamaha Страницы: 47

Бренд: Yamaha Страницы: 87

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 114

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды