Yamaha F90 Скачать руководство пользователя страница 51

Страница: 51 / 112

Engine control system

EMU26805

Alert system

NOTICE

ECM00093

Do not continue to operate the engine if an
alert device has activated. Consult your
Yamaha dealer if the problem cannot be
located and corrected.

EMU43753

Overheat alert

This engine has an overheat-alert device. If
the engine temperature rises too high, the
alert device will activate.

The engine speed will automatically de-
crease to 2000–3500 r/min.

The overheat-alert indicator will light or
blink (if equipped).

The buzzer will sound (if equipped on the
tiller handle, remote control box, or main
switch panel).

If the alert system has activated, stop the en-
gine and check the cooling water inlets:

Check trim angle to be sure that the cooling
water inlet is submerged.

Check the cooling water inlet for clogging.

EMU2685A

Low oil pressure alert

If the oil pressure drops too low, the alert de-
vice will activate.

ZMU05422

ZMU01758

ZMU04583

ZMU08288

2019 Yamaha Motor Corporation, U.S.A.

Содержание F90

















































































































Результаты поиска

Содержание F90

Отзывы:

Бренды по названию

Популярные бренды

Yamaha F90, Руководство пользователя

Результаты поиска

Содержание F90

Отзывы:

Бренды по названию

Популярные бренды