manualshive.com logo in svg

Yamaha F90, Руководство пользователя

Поделиться
Скачать
Yamaha F90 Скачать руководство пользователя страница 35

Components

29

EMU26213

Neutral throttle lever

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

TIP:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed
position.

EMU26234

Free accelerator

To open the throttle without shifting into ei-
ther forward or reverse, push the free accel-
erator button and move the remote control
lever.

TIP:

z

The free accelerator button can only be
pushed when the remote control lever is in
the neutral position.

z

After the button is pushed, the throttle be-
gins to open after the remote control lever
is moved at least 35°.

z

After using the free accelerator, return the
remote control lever to the neutral position.
The free accelerator button will return auto-
matically to its set position. The remote
control will then engage forward and re-
verse normally.

EMU25914

Tiller handle 

To change direction, move the tiller handle to
the left or right as necessary.

1. Neutral interlock trigger

1. Fully open
2. Fully closed

1

ZMU01727

1

2

N

ZMU01728

1. Fully open
2. Fully closed
3. Free accelerator

N

ZMU04576

1

3

2

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F90

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды