Yamaha F90 страница 16 Скачать руководство пользователя

Страница: 16 / 112

General information

Outboard motors affixed with this “CE” mark-
ing conform with the directives of;
2006/42/EC, 94/25/EC - 2003/44/EC,
2014/30/EU, and 2004/108/EC, 2013/53/EU.

EMU46132

Compliance mark and manu-

factured date label

Engines affixed with this label conform to the
regulations for each country.
This label is affixed to the clamp bracket or
swivel bracket.

Regulatory Compliance Mark (RCM)

Engines affixed with this mark conform to
certain portion(s) of the Australian Radio
Communications Act.

ICES-002 Compliance Label

Engines affixed with this mark meet all re-
quirements of the Canadian Interference
Causing Equipment Regulations.

1. CE marking location

ZMU08137

ZMU06040

1. Compliance mark and manufactured date

label location

1. Regulatory Compliance Mark (RCM)

1. ICES-002 Compliance Label

ZMU08071

ZMU08190

ZMU08191

2019 Yamaha Motor Corporation, U.S.A.

Содержание F90

















































































































Результаты поиска

Содержание F90

Отзывы:

Похожие инструкции для F90

Бренды по названию

Популярные бренды

Yamaha F90, Руководство пользователя

Результаты поиска

Содержание F90

Отзывы:

Похожие инструкции для F90

Бренды по названию

Популярные бренды