Yamaha F100D Скачать руководство пользователя | Manualshive

Страница: 30 / 100

background image

Components

24

the switch “

” (down) tilts the outboard motor

down and trims it down. When the switch is re-
leased, the outboard motor will stop in its cur-
rent position.
For instructions on using the power trim and
tilt switch, see pages 56 and 59.

EMU26155

Power trim and tilt switch on bottom
cowling

The power trim and tilt switch is located on the
side of the bottom cowling. Pushing the switch
“

” (up) trims the outboard motor up, and

then tilts it up. Pushing the switch “

” (down)

tilts the outboard motor down and trims it
down. When the switch is released, the out-
board motor will stop in its current position.
For instructions on using the power trim and
tilt switch, see page 59.

WARNING

EWM01031

Use the power trim and tilt switch located
on the bottom cowling only when the boat
is at a complete stop with the engine off.
Attempting to use this switch while the
boat is moving could increase the risk of
falling overboard and could distract the
operator, increasing the risk of collision
with another boat or an obstacle.

EMU30901

Variable trolling RPM switches

The trolling speed can be adjusted when the
outboard motor is trolling. Press the “

”

switch to increase the trolling speed and
press the “

” switch to decrease the trolling

speed.

1. Power trim and tilt switch

1. Variable trolling RPM switch

UP

DN

1

ZMU04231

U6D779E0.book Page 24 Tuesday, November 15, 2011 2:33 PM

«
...
28
29
30
31
32
...
»

Содержание F100D





































































































Отзывы:

Нет отзывов

Похожие инструкции для F100D

Бренд: IEI Technology Страницы: 12

Бренд: IEI Technology Страницы: 190

Бренд: IEI Technology Страницы: 8

Бренд: IEI Technology Страницы: 193

Бренд: IEI Technology Страницы: 182

KINO-DBT Series

Бренд: IEI Technology Страницы: 133

Бренд: Lantronix Страницы: 10

Бренд: ASROCK Страницы: 128

Бренд: DFI Страницы: 104

Бренд: ST Страницы: 15

Бренд: Sundance Spas Страницы: 21

Бренд: Watski Страницы: 43

Бренд: Microchip Technology Страницы: 31

Бренд: Unicorn Computer Страницы: 36

Бренд: JETWAY Страницы: 57

Бренд: Acorp Страницы: 74

Бренд: Vox Technologies Страницы: 36

Бренд: Albatron Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды