Yamaha F100D Скачать руководство пользователя

Страница: 69 / 100

Operation

EMU28062

Shallow water

EMU28081

Hydro tilt models

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

EWM00271

●

Run the boat at the lowest possible
speed when using the shallow water
cruising system.

●

Use extra care when operating in re-
verse. Too much reverse thrust can
cause the outboard motor to lift out of
the water, increasing the chance of acci-
dent and personal injury.

NOTICE

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-

ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

EMU28175

Procedure for hydro tilt models

Place the remote control lever / gear shift
lever in neutral.

Pull the tilt lock lever up to the release po-
sition.

ZMU04255

ZMU03087

U6D779E0.book Page 63 Tuesday, November 15, 2011 2:33 PM

Содержание F100D





































































































Результаты поиска

Содержание F100D

Отзывы:

Похожие инструкции для F100D

Бренды по названию

Популярные бренды

Yamaha F100D, Руководство пользователя

Результаты поиска

Содержание F100D

Отзывы:

Похожие инструкции для F100D

Бренды по названию

Популярные бренды