Yamaha F100D Скачать руководство пользователя | Manualshive

Страница: 19 / 100

background image

Specifications and requirements

13

If oil grades listed under Recommended en-
gine oil grade 1 are not available, select an al-
ternative oil grade listed under
Recommended engine oil grade 2.

Recommended engine oil grade 1

Recommended engine oil grade 2

EMU36360

Fuel requirements

EMU36803

Gasoline

Use a good quality gasoline that meets the
minimum octane rating. If knocking or pinging
occurs, use a different brand of gasoline or
premium unleaded fuel.

NOTICE

ECM01981

●

Do not use leaded gasoline. Leaded gas-
oline can seriously damage the engine.

●

Avoid getting water and contaminants in
the fuel tank. Contaminated fuel can
cause poor performance or engine dam-
age. Use only fresh gasoline that has
been stored in clean containers.

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol (E10) and that containing
methanol. Ethanol can be used if the ethanol
content does not exceed 10% and the fuel
meets the minimum octane ratings. E85 is a
fuel containing 85% ethanol and must not be
used in your outboard motor. All ethanol
blends containing more than 10% ethanol can
cause fuel system damage or cause engine
starting and running problems. Yamaha does
not recommend gasohol containing methanol
because it can cause fuel system damage or
engine performance problems.
It is recommended that you install a water-
separating marine fuel filter assembly (10 mi-
cron minimum) between your boat’s fuel tank
and outboard motor when using ethanol. Eth-
anol is known to allow moisture to be ab-
sorbed into boat fuel tanks and systems.

Recommended engine oil:

4-stroke outboard motor oil

Recommended engine oil grade 1:

SAE 10W-30/10W-40/5W-30
API SE/SF/SG/SH/SJ/SL

Recommended engine oil grade 2:

SAE 15W-40/20W-40/20W-50
API SH/SJ/SL
Engine oil quantity (without oil filter re-
placement):

3.5 L (3.70 US qt, 3.08 Imp.qt)

Engine oil quantity (with oil filter re-
placement):

3.7 L (3.91 US qt, 3.26 Imp.qt)

ZMU06854

122˚F

50˚C

104

40

86

30

68

SAE

API

SE
SF

SG
SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

10W–30

10W–40

5W–30

ZMU06855

122˚F

50˚C

104

40

86

30

68

SAE

API

SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

15W–40

20W–40

20W–50

Recommended gasoline:

Regular unleaded gasoline with a
minimum octane rating of 90 (Re-
search Octane Number).

U6D779E0.book Page 13 Tuesday, November 15, 2011 2:33 PM

«
...
17
18
19
20
21
...
»

Содержание F100D





































































































Отзывы:

Нет отзывов

Похожие инструкции для F100D

Бренд: Abit Страницы: 112

Бренд: Lantronix Страницы: 17

Бренд: NXP Semiconductors Страницы: 12

Бренд: Advantech Страницы: 3

Бренд: Gigabyte Страницы: 36

ML501MicroBlaze

Бренд: Xilinx Страницы: 46

Бренд: Xilinx Страницы: 55

Бренд: Xilinx Страницы: 88

Бренд: Avalue Technology Страницы: 116

Бренд: MAX power Страницы: 20

Бренд: DFI Страницы: 177

nForce 680i LT SLI

Бренд: XFX Страницы: 137

Бренд: ECS Страницы: 87

Бренд: ON Semiconductor Страницы: 20

Бренд: DFI Страницы: 99

Бренд: Supermicro Страницы: 121

Бренд: Supermicro Страницы: 20

Бренд: Supermicro Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды