Yamaha Disklavier E3 Series Скачать руководство пользователя страница 44

Страница: 44 / 52

3.Error Messages that Occur During Measurement

The following error messages may appear when an error occurs during or after
measuring in the service center mode.
Carry out the appropriate remedy.

During Sensor Management

Error Messages

Situation

Remedy

E1:KS REST AD is too low

The rest value is too low (too dark).

Check the key sensor’s height adjustment.

Check the sensor head position and key shutter.

Carry out the measurement again.

E1:KS END AD is too high

The end value is too high (the

difference between the rest and end

value is too low).

Check the key adjustment (pay particular

attention to uneven keys in the balance section).

Check the key rail adjustment (the space

between the key rail and the keyboard is not

large enough).

Check the key sensor’s height adjustment.

Check sensor head position and key shutter.

Carry out the measurement again.

During Pedal Measurement

Error Messages

Situation

Remedy

Loud Stroke : E1

Damper pedal stroke is short.



Playback with backup table.

Pedal adjustment.

Re-measure.

Soft Stroke : E1

Shift pedal stroke is short.



Playback with backup table.

Pedal adjustment.

Re-measure.

Calibration : E1

Cannot determine half point.



Playback with backup table.

Pedal adjustment.

Half point adjustment.

Содержание Disklavier E3 Series





















































Результаты поиска

Содержание Disklavier E3 Series

Отзывы:

Yamaha Disklavier E3 Series, Руководство по обслуживанию, Страница: 44 / 52

Результаты поиска

Содержание Disklavier E3 Series

Отзывы: