manualshive.com logo in svg

Yamaha Disklavier E3 Series, Руководство по обслуживанию

Поделиться
Скачать
Yamaha Disklavier E3 Series Скачать руководство пользователя страница 33

 18 

  6-1.CTRL SHEET TEST 
 
 
 
 
 
 
 
 
 
 
 
 
                                                     
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

↓↑

 

 

=TEST MODE= 

 MODEL:E3 
 PIANO:UPS           (↓) 

 =TEST MODE= 
 CTRL SHEET 
               (↓,↑,→) 

 V2.00   Jan 22 2009 
 800  ENG REC UP S  DB51  
  

 (1) LED Test 

 

 (2) OELD Test  

 

 (3)  Sound Test 

        Press [PLAY] 

 

 (4) Switch Test 

    (Switch & Rmt Ctl)

 

 (5) DRAM Test 
        Press [PLAY]     

 

 (6) Flash Read Test 

       Press [PLAY]     

 

 (7) Host I/O Test
 
 Please wait

 

 (8)   MIDI I/O Test

 

 (9) Calendar Test & Set 
 2008/07/31(Thu) 12:00:00 

Displays the Version number of CTRL sheet. 
 Model setting  

[UP/DOWN]cursor: to select GP/UP,  [REC]: “Quiet ON/OFF”  

Check if LED lights up correctly. 

  

 (2) OELD Test  

 

 

(2) OELD Test  

 

 (3)  Sound Test

        1000   Hz

 

(3)  Sound Test

        2000   Hz

 

 (5) DRAM Test
  wait 30 sec.      

 

(5) DRAM Test

            OK!

 

 (6) Flash Read Test
 OK!   

 

 (7) Host I/O Test
 
 Vendor=0499 ProdID=2003

 

←

 

→

 

Check the organic electro luminescence display. 

Press the [PLAY/PAUSE] button to execute the test. 
Check the internal sound. 

Press the buttons on the control unit and remote controller 
to check the buttons. 

Press the [PLAY/PAUSE] button to execute the test. 
DRAM test of the CTRL sheet will be executed and “OK” will be displayed if 
no error is detected.    It will takes about 30 seconds   

Connect the [USB TO DEVICE] and [USB TO HOST] ports on the back 
side of the control unit with a USB cable, and then execute the test. 
Check the numbers shown above.   

Connect the [MIDI OUT] and [MIDI IN] terminals on the back side of the 
control unit with a MIDI cable and then execute the test. 

Setting: 
 [ENTER]   : setup mode ON/OFF 
 [REC]      : Left item 
 [SELECT]  : Right item 
  [UP/DOWN] : to change the value 

31 

Содержание Disklavier E3 Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды