Yamaha Disklavier E3 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

background image

11

・

XG Tone Generator Functions

Using the procedure described above,
select an ensemble song for playback
from the supplied CD.

Listen to the ensemble tone generator
playback from the speaker to check
sound output.
*Make sure that the speaker power is
switched ON.
*Make sure that speaker volume is

turned up.

・

Recording Function



Playback



Delete

Press the [SELECT] button.

Select “Memory”.

Press the [RECORD] button.

Press the [PLAY] button.

Start playing on the keyboard.
Play all 88 keys (1 to 88) and operate
each of the pedals.

Press the [STOP] button.

Use the same procedure to playback
the song you just recorded.

Press the [FUNC.] button.

Select “DELETE SONG”.

Select the song you played then press
the [ENTER] button.

Press the [+/YES] button.

・

Switch the power OFF

Press the power switch on the control
unit to switch the power off.

13

«
...
13
14
15
16
17
...
»

Содержание Disklavier E3 Series





















































Отзывы:

Нет отзывов

Похожие инструкции для Disklavier E3 Series

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 74

Бренд: Omega Engineering Страницы: 22

Бренд: Unico Страницы: 10

Бренд: Wavetek Страницы: 43

Бренд: Aqua Lung Страницы: 24

Бренд: Stübbe Страницы: 12

Бренд: Dewetron Страницы: 24

Бренд: Technoline Страницы: 1

Бренд: Conrad Electronic Страницы: 38

Orion Versa Star Pro Series

Бренд: Thermo Scientific Страницы: 4

Бренд: AKCP Страницы: 16

Бренд: Swann Страницы: 106

Бренд: red lion Страницы: 4

IronHeart IRT120H

Бренд: Laney Страницы: 20

Бренд: TESTO Страницы: 61

Бренд: Caird Technology Страницы: 29

Бренд: McIntosh Страницы: 17

Бренд: Digi-Sense Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды