manualshive.com logo in svg

Yamaha CRW6416S Series, Руководство пользователя

"Yamaha CRW6416S Series" - высококачественный CD-RW привод с возможностью записи и перезаписи дисков. Для получения инструкции по эксплуатации загрузите бесплатное Руководство пользователя на manualshive.com. Получите полное понимание работы вашего устройства, следуя инструкциям из руководства. Узнайте все возможности "Yamaha CRW6416S Series" прямо сейчас!

Поделиться
Скачать
background image

8

Connect the audio cable between the CRW6416S drive and the computer’s
sound card, or the motherboard’s audio connector if it has built-in audio.
One end of the audio cable has two connectors: a smaller type and a larger
type.  Choose one that matches your sound card’s connector.  The connector
at other end of the cable is connected to “AUDIO OUT” of the CRW6416S
drive.  Make sure connector’s lug is at the top.

n

You do not need to connect the audio cable to write audio CDs since the audio is passed over
the SCSI bus.  It is required for playing back audio CDs on the CRW6416S drive via the
computer’s sound card.  However, if a CD-ROM drive is already connected to the sound card,
you should use this drive to play back your audio CDs.  To listen to audio CDs without a
computer sound card, connect headphones or speakers to the headphone jack on the
CRW6416S drive’s front panel.

AUDIO

  OUT

ID SEL

ECT

PARITY

TERM

INATO

R

BLOCK

 SIZE

SCSI

INTER

FACE

CONN

ECTOR

DC IN

PUT

1

+5V

G

+12V

R

L

1 2 4

G

Sound card

Audio cable

Lug

18

Installation

6416S_e15.qx  6/29/99  6:00 PM  Page 25

Содержание CRW6416S Series



















































Отзывы:

Нет отзывов

Похожие инструкции для CRW6416S Series

Danfoss VLT AQUA Drive FC 202 Programming Manual preview
VLT AQUA Drive FC 202
Бренд: Danfoss Страницы: 294
BENSHAW RSi H2P Series Instruction Manual preview
RSi H2P Series
Бренд: BENSHAW Страницы: 47
IBM 71P7285 User Manual preview
71P7285
Бренд: IBM Страницы: 121
Parker 890SD Engineering Reference preview
890SD
Бренд: Parker Страницы: 54
Kenwood TrueX 72X Quick Install Manual preview
TrueX 72X
Бренд: Kenwood Страницы: 2
Kenwood TrueX Series Quick Install Manual preview
TrueX Series
Бренд: Kenwood Страницы: 2
Leadshine EM556-CAN User Manual preview
EM556-CAN
Бренд: Leadshine Страницы: 33
KB Electronics KBBC Series Operating Instructions preview
KBBC Series
Бренд: KB Electronics Страницы: 5
KB Electronic 9572 Installation And Operation Manual Supplemental Information preview
9572
Бренд: KB Electronic Страницы: 18
SHS HT7 Series User Manual preview
HT7 Series
Бренд: SHS Страницы: 29
SHS HT3 Series User Manual preview
HT3 Series
Бренд: SHS Страницы: 33
Baumuller BM5-SSL Instruction Handbook Manual preview
BM5-SSL
Бренд: Baumuller Страницы: 80
Afag BF10 Translation Of Original Operating Instructions preview
BF10
Бренд: Afag Страницы: 19
ACDelco ARD2081 Product Information Manual preview
ARD2081
Бренд: ACDelco Страницы: 36
YASKAWA FP65U T Series Installation & Primary Operation preview
FP65U T Series
Бренд: YASKAWA Страницы: 106
YASKAWA HV600 Manual preview
HV600
Бренд: YASKAWA Страницы: 610
YASKAWA VS-616PS5 Series Quick Start Manual preview
VS-616PS5 Series
Бренд: YASKAWA Страницы: 109
ABB ACS880-01+C135 Series Supplement Manual preview
ACS880-01+C135 Series
Бренд: ABB Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды