manualshive.com logo in svg

Yamaha CRW6416S Series, Руководство пользователя

Поделиться
Скачать
Yamaha CRW6416S Series Скачать руководство пользователя страница 18

11

Installation

2

Parity Check

The parity check is used for error correction during data transmissions.  If
parity-checking has to be disabled, the shunt on the Parity jumper switch should
be removed.

n

By factory default, the Parity switch is set to “on” and should normally be left in this state.

3

Termination

Terminators prevent SCSI signals from being reflected off the last device in the
chain.  The SCSI terminator switch should be set to “on” if the CRW6416S is the
last device on the internal SCSI chain. If the CRW6416S is not the last device on
the internal SCSI chain, the shunt on the Terminator jumper switch should be
removed.

n

By factory default, the Terminator switch is set to “on.”

Computer

CRW6416S
(terminated)

Hard disk drive

(unterminated)

MO drive

(terminated)

Terminator

SCSI adapter card

ID SELECT

PARITY

TERMINATOR
BLOCK SIZE

1 2 4

ID SELECT

PARITY

TERMINATOR
BLOCK SIZE

1 2 4

Parity on 

(Default)

Parity off

6416S_e15.qx  6/29/99  6:00 PM  Page 18

Содержание CRW6416S Series



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды