AW2816
78
DISPLAY MESSAGE LIST
Messages
AUTOMIX DISABLED.
Automix is not enabled, and cannot be recorded.
AUTOMIX MEMORY FULL!
Automix memory has no free area.
AUTOMIX NOT RUNNING.
Automix has been stopped, so recording is not possible. Pause the
recorder, and then playback.
AUTOMIX REC ABORTED.
Automix recording was stopped, and the data was discarded.
AUTOMIX RECORDING.
The operation cannot be executed since automix is being recorded.
AUTOMIX RUNNING.
The operation cannot be executed since automix is being recorded or
played.
BULK: BYTE COUNT MISMATCH!
The data length specified within the received system exclusive data
did not match the length of the data that was actually received.
BULK: CHECKSUM MISMATCH!
The check sum of the received system exclusive is incorrect.
BULK: MEMORY PROTECTED!
The scene memory you attempted to receive is protected.
CANNOT ASSIGN DIGITAL-ST-IN.
DIGITAL STEREO IN cannot be assigned to the stereo bus cascade.
CANNOT CHANGE THE MUTE
Muting cannot be defeated since this would exceed the number of
simultaneously playable tracks.
CANNOT PLAY THIS PAGE
Playback is not possible in this page.
CANNOT RECALL AUTOMIX
Recall is not possible, since automix data has not been stored.
CANNOT REDO
Redo (re-execution of an operation) is not possible.
CANNOT SET MARK
It is not possible to specify a mark at an already-specified position.
CANNOT UNDO
Undo (cancellation of an operation) is not possible.
CD PLAY MODE NOW.
Since the AW2816 is in CD Play mode, this operation is not possible.
DIFFERENT TC FRAME TYPE
MTC of a different frame type than the internal setting is being
received.
DIGITAL-ST-IN REC PROHIBIT.
Recording is prohibited for the signal being input from DIGITAL STE-
REO IN.
DIGITAL-ST-IN SYNC ERROR!
The signal being input from DIGITAL STEREO IN is not synchronized
to the word clock master.
DIN TO STEREO BUS REFUSE.
Since the signal was interrupted, cascading from DIGITAL STEREO IN
to the stereo bus has been defeated.
DISK BUSY
The reading speed of the internal hard disk is not fast enough, or the
reading speed has slowed down because the recorded data has
become fragmented.
DRIVE NOT READY
The drive is not ready.
EFF1 INSERT RELEASED
Effect 1 has been released from insertion because a patch library was
recalled.
EFF2 INSERT RELEASED
Effect 2 has been released from insertion because a patch library was
recalled.
FOR EFFECT2 ONLY.
The selected effect program can be used only with effect 2.
IN/OUT POINTS TOO CLOSE
The auto punch-in/out interval is too short. It cannot be set less than
approximately 100 msec.
INT.EFF NOW SELECTED AUX.
The internal effect is connected to the AUX send, and cannot be
inserted.
LOW BATTERY!!
The internal battery is running down.
Содержание AW2816
