Yamaha 9.9F Скачать руководство пользователя | Manualshive

Страница: 49 / 62

background image

Maintenance

44

EMU28957

Cleaning and adjusting spark plug

The spark plug is an important engine compo-
nent and is easy to inspect. The condition of
the spark plug can indicate something about
the condition of the engine. For example, if the
center electrode porcelain is very white, this
could indicate an intake air leak or carburetion
problem in that cylinder. Do not attempt to di-
agnose any problems yourself. Instead, take
the outboard motor to a Yamaha dealer. You
should periodically remove and inspect the
spark plug because heat and deposits will
cause the spark plug to slowly break down
and erode.
1.

Remove the spark plug caps from the
spark plugs.

2.

Remove the spark plug. If electrode ero-
sion becomes excessive, or if carbon and
other deposits are excessive, you should
replace the spark plug with another of the
correct type.

WARNING! When remov-

ing or installing a spark plug, be care-
ful not to damage the insulator. A
damaged insulator could allow exter-
nal sparks, which could lead to explo-
sion or fire.

[EWM00561]

3.

Be sure to use the specified spark plug,
otherwise the engine may not operate
properly. Before fitting the spark plug,
measure the electrode gap with a wire
thickness gauge; replace it if out of spec-
ification.

4.

When fitting the plug, wipe off any dirt
from the threads, and then screw it in to
the correct torque.

TIP:

If a torque-wrench is not available when you
are fitting a spark plug, a good estimate of the
correct torque is 1/4 to 1/2 a turn past finger-
tight. Have the spark plug adjusted to the cor-
rect torque as soon as possible with a torque-
wrench.

EMU37450

Checking fuel filter

Check the fuel filter periodically. If any water
or foreign matter is found in the filter, clean or
replace it. For cleaning or replacement of the
fuel filter, consult your Yamaha dealer.

EMU29044

Inspecting idle speed

WARNING

EWM00451

●

Do not touch or remove electrical parts
when starting or during operation.

Standard spark plug:

B7HS-10
BR7HS-10

1. Spark plug gap

2. Spark plug part number

3. Spark plug I.D. mark (NGK)

Spark plug gap:

0.9–1.0 mm (0.035–0.039 in)

Spark plug torque:

25.0 Nm (2.55 kgf-m, 18.4 ft-lb)

U63V2DE0.book Page 44 Monday, February 22, 2010 9:00 AM

«
...
47
48
49
50
51
...
»

Содержание 9.9F































































Отзывы:

Нет отзывов

Похожие инструкции для 9.9F

Бренд: Danbit Страницы: 70

Бренд: NXP Semiconductors Страницы: 14

Бренд: Microchip Technology Страницы: 17

PCM-8152 3rd Generation

Бренд: Aaeon Страницы: 6

conga-HPC/EVAL-Server

Бренд: Congatec Страницы: 54

Бренд: ASROCK Страницы: 145

Бренд: MSI Страницы: 30

Бренд: MSI Страницы: 71

Бренд: AOpen Страницы: 8

Бренд: Advantech Страницы: 82

Бренд: ICP Страницы: 50

Бренд: Aaeon Страницы: 113

Бренд: JETWAY Страницы: 46

Бренд: Intel Страницы: 29

Бренд: ST Страницы: 47

Z77A-GD65 GAMING series

Бренд: MSI Страницы: 98

Бренд: ASROCK Страницы: 2

Бренд: AOpen Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды