Yamaha 9.9F Скачать руководство пользователя | Manualshive

Страница: 35 / 62

background image

Operation

30

●

Start the engine, and then check that the
engine stops when the engine stop button
is pushed.

●

Restart the engine, and then check that the
engine stops when the clip is pulled from
the engine shut-off switch.

●

Check that the engine cannot be started
with the clip removed from the engine shut-
off switch.

EMU34550

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

NOTICE

ECM01610

Warm up the engine before shifting into
gear. Until the engine is warm, the idle
speed may be higher than normal. High
idle speed can prevent you from shifting
back to neutral. If this occurs, stop the en-
gine, shift to neutral, then restart the en-
gine and allow it to warm up.

To shift out of neutral
Move the gear shift lever firmly and crisply for-
ward (for forward gear) or backward (for re-
verse gear). Be sure to check that the tilt lock
lever is in the lock/down position (if equipped)
before operating in reverse.

To shift from in gear (forward/reverse) to neu-
tral
1.

Close the throttle so that the engine
slows to idle speed.

2.

After the engine is at idle speed in gear
move the gear shift lever firmly and crisp-
ly into the neutral position.

ZMU02030

U63V2DE0.book Page 30 Monday, February 22, 2010 9:00 AM

«
...
33
34
35
36
37
...
»

Содержание 9.9F































































Отзывы:

Нет отзывов

Похожие инструкции для 9.9F

Бренд: JETWAY Страницы: 48

Бренд: NXP Semiconductors Страницы: 12

TITAN TURBO PLUS ATX

Бренд: TYAN Страницы: 69

Бренд: IWILL Страницы: 54

Бренд: TYAN Страницы: 86

Бренд: JETWAY Страницы: 58

FEBFAN6604MR_CH11U65A

Бренд: Fairchild Страницы: 22

Бренд: DFI Страницы: 139

Бренд: ASROCK Страницы: 88

RACK EP2C612D16C-4L

Бренд: ASROCK Страницы: 92

QC5000-ITX/WiFi

Бренд: ASROCK Страницы: 125

Бренд: ASROCK Страницы: 123

Бренд: Abit Страницы: 96

Бренд: ASROCK Страницы: 63

Бренд: ASROCK Страницы: 69

Бренд: ASROCK Страницы: 168

Бренд: Texas Instruments Страницы: 24

Бренд: Texas Instruments Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды