manualshive.com logo in svg

Yamaha 9.9F, Руководство пользователя

Поделиться
Скачать
Yamaha 9.9F Скачать руководство пользователя страница 20

Components

15

EMU26002

Engine stop button

The engine stop button stops the engine
when the button is pushed.

EMU26030

Choke knob

To supply the engine with the rich fuel mixture
required to start, pull out this knob. The choke
knob has the 4 operating positions shown in
the following illustration.

EMU26073

Manual starter handle

The manual starter handle is used to crank
and start the engine.

EMU26122

Steering friction adjuster

A friction device provides adjustable resis-
tance to the steering mechanism, and can be
set according to operator preference. An ad-
justing screw or bolt is located on the swivel
bracket.

1. Cord

2. Clip

3. Engine shut-off switch

1. Use to start a hot engine

2. Use to warm up a cold engine or restart a 

warm engine

3. Use to warm up a cold engine or restart a 

warm engine

4. Use to start a cold engine

U63V2DE0.book  Page 15  Monday, February 22, 2010  9:00 AM

Содержание 9.9F































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды