Yamaha 250G Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 76

Yamaha 250G Скачать руководство пользователя страница 62

Maintenance

57

to drain completely.

CAUTION:

ECM00710

Inspect the used oil after it has been
drained. If the oil is milky, water is getting
into the gear case which can cause gear
damage. Consult a Yamaha dealer for re-

pair of the lower unit seals.

NOTE:

For disposal of used oil consult your Yamaha

dealer.

5.

With the outboard motor in a vertical po-
sition, and using a flexible or pressur-
ized filling device, inject the gear oil into
the gear oil drain screw hole.

6.

When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil
level plug.

7.

Insert and tighten the gear oil drain
screw.

EMU29312

Inspecting and replacing anode(s)

Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect the
external anodes periodically. Remove scales
from the surfaces of the anodes. Consult a
Yamaha dealer for replacement of external
anodes.

CAUTION:

ECM00720

Do not paint anodes, as this would render

them ineffective.

NOTE:

Inspect ground leads attached to external
anodes on equipped models. Consult a
Yamaha dealer for inspection and replace-
ment of internal anodes attached to the pow-

er unit.

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

250GETO 1150.0 cm

3

(38.88 US oz)

(40.56 Imp.oz)
L250GETO 1000.0 cm

3

(33.81 US oz)

(35.27 Imp.oz)

ZMU03274

ZMU01901

ZMU05313

«
...
60
61
62
63
64
...
»

Содержание 250G













































































Отзывы:

Нет отзывов