Yamaha 250G Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 76

Yamaha 250G Скачать руководство пользователя страница 19

Basic components

14

NOTE:

The water separator and engine trouble
warning indicators only operate when the en-
gine is equipped with the appropriate func-

tions.

EMU26550

Oil level indicator (digital type)

This indicator shows the engine oil level. If
the oil level falls below the lower limit, the
warning indicator will start to blink. For fur-
ther information, see page 21.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

EMU26581

Overheat warning indicator (digital
type)

If the engine temperature rises too high, the
warning indicator will start to blink. For fur-
ther information on reading the indicator, see
page 20.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious

engine damage will occur.

EMU26600

Speedometer (digital type)

This gauge shows the boat speed.

NOTE:

After the main switch is first turned on, all
segments of the display come on as a test.
After a few seconds, the gauge will change
to normal operation. Watch the gauge when
turning on the main switch to make sure all

segments come on.

NOTE:

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-

1. Oil level indicator

1

ZMU01867

1. Overheat warning indicator

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Warning indicator(s)

ZMU04632

1

«
...
17
18
19
20
21
...
»

Содержание 250G













































































Отзывы:

Нет отзывов