Yamaha 250G Скачать руководство пользователя страница 46

Страница: 46 / 76

Maintenance

EMU28217

Specifications

Dimension:

Overall length:

854 mm (33.6 in)

Overall width:

562 mm (22.1 in)

Overall height X:

1785 mm (70.3 in)

Transom height X:

641 mm (25.2 in)

Weight (SUS) X:

250GETO 240.0 kg (529 lb)
L250GETO 242.0 kg (534 lb)

Performance:

Full throttle operating range:

4500–5500 r/min

Maximum output:

183.9 kW@5000 r/min (250
HP@5000 r/min)

Idling speed (in neutral):

700

25 r/min

Engine:

Type:

2-stroke V

Displacement:

3130.0 cm

(190.99 cu.in)

Bore

stroke:

90.0

82.0 mm (3.54

3.23 in)

Ignition system:

CDI (micro computer)

Spark plug (NGK):

BR8HS-10

Spark plug gap:

0.9–1.0 mm (0.035–0.039 in)

Control system:

Remote control

Starting system:

Electric

Starting carburetion system:

Choke valve

Min. cold cranking amps (CCA/EN):

711.0 A

Min. rated capacity (20HR/IEC):

100.0 Ah

Alternator output for battery DC:

35.0 A

Drive unit:

Gear positions:

Forward-neutral-reverse

Gear ratio:

1.81 (29/16)

Trim and tilt system:

Power trim and tilt

Propeller mark:

250GETO T / M
L250GETO TL / ML

Fuel and oil:

Recommended fuel:

Regular unleaded gasoline

Min. research octane:

Recommended engine oil:

YAMALUBE 2-stroke outboard motor
oil

Lubrication:

Oil injection

Engine oil tank capacity:

1.2 L (1.27 US qt) (1.06 Imp.qt)

Remote oil tank capacity:

10.5 L (11.10 US qt) (9.24 Imp.qt)

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

250GETO 1150.0 cm

(38.88 US oz)

(40.56 Imp.oz)
L250GETO 1000.0 cm

(33.81

US oz) (35.27 Imp.oz)

Tightening torque for engine:

Spark plug:

25.0 Nm (18.4 ft-lb) (2.55 kgf-m)

Propeller nut:

Содержание 250G













































































Результаты поиска

Содержание 250G

Отзывы:

Yamaha 250G, Руководство пользователя, Страница: 46 / 76

Результаты поиска

Содержание 250G

Отзывы: