Yamaha 250G Скачать руководство пользователя страница 43

Страница: 43 / 76

Operation

EMU28053

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

Release the tilt support lever or pull out
the tilt support knob.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-

ZMU05306

ZMU01936

ZMU04603

ZMU05317

Содержание 250G













































































Результаты поиска

Содержание 250G

Отзывы:

Yamaha 250G, Руководство пользователя, Страница: 43 / 76

Результаты поиска

Содержание 250G

Отзывы: