Yamaha 2002 FZS600 Скачать руководство пользователя страница 65

Страница: 65 / 74

–58–

SIGNAL SYSTEM

ELEC

Tester (+) lead

Brown terminal

Tester (–) lead

BLACK terminal

Fuel sender resistance

: 4

Ω

at 20

: 122.5

128.5

Ω

at 20

Tester (+) lead

Green terminal

Tester (–) lead

Black terminal

1. Bulb and bulb socket

Check the bulb and bulb socket for continu-
ity.

Replace the bulb and / or bulb socket.

CONTINUITY

NO CONTINUITY

2. Fuel sender

Drain the fuel and remove the fuel sender
from the fuel tank.

Disconnect the fuel sender coupler from the
wire harness.

Connect the pocket tester (

Ω

1) to the fuel

sender.

Check the fuel sender for continuity.

MEETS
SPECIFICATION

Replace the fuel sender.

OUT OF SPECIFICATION

Measure the fuel sender resistance.

3
4

3. Voltage

Connect the pocket tester (DC 20 V) to the
meter assembly coupler.

Drain the fuel.

Turn the main switch to “ON”.

Check the voltage (12 V).

The wiring circuit from the main switch to the
bulb socket connector is faulty, repair it.

MEETS
SPECIFICATION

OUT OF SPECIFICATION

SIGNAL SYSTEM CHECK

1. If the fuel level warning light fails to come on

or the fuel meter fails to operate:

Содержание 2002 FZS600











































































Результаты поиска

Содержание 2002 FZS600

Отзывы:

Похожие инструкции для 2002 FZS600

Бренды по названию

Популярные бренды

Yamaha 2002 FZS600, Дополнительное руководство по обслуживанию

Результаты поиска

Содержание 2002 FZS600

Отзывы:

Похожие инструкции для 2002 FZS600

Бренды по названию

Популярные бренды