Yamaha 2002 FZS600 Скачать руководство пользователя страница 21

Страница: 21 / 74

–14–

CABLE ROUTING

SPEC

A Using clamp, fix to the front fork:

Right handlebar switch lead

Brake hose

Locate clamp with its head in-
ward of frame.

B Pass throttle cables through

guide.
Throttle cable installed to upper
bracket.

C With its pulling side on top. Pass

throttle cable innermost of
clamp.

D Pass main switch lead under:

Throttle cable (2 pcs)

Right handlebar switch lead

Speed sensor lead

And them into box at right side. In
so doing, give leads some slack.

E Pass throttle cable under box.

F Pass through holder on frame:

Radiator reservoir tank breath-
er hose

Fuel tank breather hose

G To reservoir tank

H Pass battery negative lead on

the inside of radiator reservoir
tank breather hose.

I Using clamp, fix stop switch lead

to frame. Locate clamp with its
latch outward of frame.

J Pass on the inside of side cover

insertion position.

Содержание 2002 FZS600











































































Результаты поиска

Содержание 2002 FZS600

Отзывы:

Похожие инструкции для 2002 FZS600

Бренды по названию

Популярные бренды

Yamaha 2002 FZS600, Дополнительное руководство по обслуживанию

Результаты поиска

Содержание 2002 FZS600

Отзывы:

Похожие инструкции для 2002 FZS600

Бренды по названию

Популярные бренды