Yamaha 2002 FZS600 Скачать руководство пользователя страница 48

Страница: 48 / 74

–41–

FRONT FORK

CHAS

WARNING

NOTE:

WARNING

NOTE:

WARNING

EB703100

REMOVING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.
1. Stand the motorcycle on a level surface.

Securely support the motorcycle so that
there is no danger of it falling over.

Place the motorcycle on a suitable stand so
that the front wheel is elevated.

2. Loosen:

upper bracket pinch bolt

cap bolt

lower bracket pinch bolt

Before loosening the upper and lower
bracket pinch bolts, support the front fork
leg.

3. Remove:

front fork leg

EB703710

INSTALLING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.
1. Install:

front fork leg
Temporarily tighten the upper and lower
bracket pinch bolts.

Make sure that the inner fork tube is flush
with the top of the handlebar holder.

2. Tighten:

lower bracket pinch bolt

cap bolt

upper bracket pinch bolt

Lower bracket pinch bolt

30 Nm (3.0 m

kg)

Cap bolt

23 Nm (2.3 m

kg)

Upper bracket pinch bolt

30 Nm (3.0 m

kg)

Make sure that the brake hoses are routed
properly.

Содержание 2002 FZS600











































































Результаты поиска

Содержание 2002 FZS600

Отзывы:

Похожие инструкции для 2002 FZS600

Бренды по названию

Популярные бренды

Yamaha 2002 FZS600, Дополнительное руководство по обслуживанию

Результаты поиска

Содержание 2002 FZS600

Отзывы:

Похожие инструкции для 2002 FZS600

Бренды по названию

Популярные бренды