Yale E878 страница 56 Скачать руководство пользователя

Страница: 56 / 64

WARNING

Keep  park  brake  applied,  full  service  brake  ap-
plied,  and  full  accelerator  applied  during  entire
time  that  automated  transmission  valve  calibra-
tion is occurring.

Refer to Table 20 for the procedures on how to per-
form Proc_Cal_016: Transmission Valve Calibration.

Table 20. Proc_Cal_016B: Transmission Valve Calibration

A. TYPICAL DISPLAY WITHOUT KEY, WITH OPTIONS
B. TYPICAL DISPLAY WITH KEY, WITHOUT OPTIONS

Information:

Parking Brake and Service Brakes MUST be properly adjusted and functioning before performing

this procedure.

Perform Proc_Cal_001: Service Password Entry before proceeding.

Action:

Start Engine.

You Will See:

Main Menu
Passwords

Step 1: Press

Until You See:

Main Menu
Calibrations

Step 2: Press

One Time

You Will See:

Calibrations
Lift Valve Output

Step 3: Press

Until You See:

Calibrations
Calibrate Xsmn Valve

Step 4: Press

One Time

You Will See:

Calibrate Xsmn Valve
Press

to Begin

Action 1:

APPLY Parking Brake and leave on throughout process.

Action 2:

FULLY APPLY Service Brakes and HOLD during process.

Action 3:

FULLY Depress Accelerator Pedal and HOLD during process.

Action 4:

Allow for the transmission to warm up to 60°C (140°F).

Information:

This is an automated process. The Engine, Park Brake, and Service Brake must all be ON for the

process to start.

If either Parking or Service Brake is NOT applied, you will
see.....

Apply Parking Brake
Apply Service Brake

If both Parking and Service Brakes are applied, you will
see.....

Calibrate Xmsn Valve
Press

to Begin.

Proc_Cal_016B: Trans. Valve Calibration-Electronic and Electronic Extended
Function

8000 YRM 1134

Confidential/Proprietary - Do Not Copy or Duplicate

Содержание E878

































































Результаты поиска

Содержание E878

Отзывы:

Похожие инструкции для E878

Бренды по названию

Популярные бренды

Yale E878, Руководство по обслуживанию

Результаты поиска

Содержание E878

Отзывы:

Похожие инструкции для E878

Бренды по названию

Популярные бренды