Yale E878 страница 59 Скачать руководство пользователя | Manualshive

Страница: 59 / 64

background image

Table 21. Proc_Cal_019: Mazda LP and Gas Accelerator Pedal Adjustment (Continued)

Action:

Transmission in neutral.

Action:

Park brake applied.

You Will See:

Main Menu
Passwords

Step 1: Press

or

Until You See:

Main Menu
Calibrations

Step 2: Press

*

One Time

You Will See:

Calibrations
Lift Valve Output

Step 3: Press

or

Until You See:

Calibrations
Accelerator Pedal

Step 4: Press

*

One Time

You Will See:

Accel Pedal xx%
Xxx RPM

Information:

Top line will show numbers for percent of pedal travel. Bottom line is engine RPM.

Action 1:

With the engine warm (80°C (176°F)

minimum coolant temperature) and at idle,
slowly press the throttle pedal until the engine
RPM reaches 850. The accelerator pedal value
should be between 22 and 27 percent.

You Will See:

Accel Pedal 25%
850 RPM

Action 2 (LPG) :

If this value is below 22 percent, then adjust slack into the cable by adjusting the nuts on

the engine throttle cable bracket. If the value is above 27 percent, remove the slack in the cable by adjust-
ing the same nuts. If there is not enough adjustment, verify that the bell crank to cowl clearance is correct.
When adjustment is complete, tighten throttle cable adjusting screws to 8 to 15 N•m (6 to 11 lbf ft). Refer
to the

Frame

section for your lift truck for complete adjustment procedures.

Action 2 (Gas) :

If this value is below 22 percent, increase the clearance between the bellcrank screw

and the bellcrank follower by adjusting the bellcrank screw. If the value is above 27 percent, decrease the
clearance between the bellcrank screw and the bellcrank follower by adjusting the bellcrank screw. When
adjustment is complete, lock the adjusting screw with the jam nut. Refer to the

Frame

section for your lift

truck for complete adjustment procedures.

Action 3:

Adjust bumper on the underside of the throttle pedal and tighten jam nut as shown in the

Frame

section for your lift truck.

Action:

Ignition

OFF

.

8000 YRM 1134

Proc_Cal_019: Mazda LP and Gas Accelerator Pedal Adjustment

Confidential/Proprietary - Do Not Copy or Duplicate

53

«
...
57
58
59
60
61
...
»

Содержание E878

































































Отзывы:

Нет отзывов

Похожие инструкции для E878

Бренд: Raymarine Страницы: 464

Бренд: 3M Страницы: 8

Бренд: ZOLL Страницы: 3

Бренд: JB-Lighting Страницы: 60

Бренд: Cambro Страницы: 6

Бренд: h/p/cosmos Страницы: 81

Бренд: M-Audio Страницы: 25

Бренд: National Instruments Страницы: 10

Бренд: PARUS Страницы: 6

Бренд: Vahterus Страницы: 31

Littmann Classic II Pediatric

Бренд: 3M Страницы: 53

Бренд: Eleiko Страницы: 4

Бренд: Heiniger Страницы: 164

Бренд: Hausmann Страницы: 10

Бренд: Qtx Страницы: 6

Бренд: Hussmann Страницы: 20

LIGHT LINEAR PT 1

Бренд: LIGMAN Страницы: 6

Бренд: QRS Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды